Aeri is technically an archtop. It looks like one, it behaves like one acoustically, and it carries the lineage of one. But it is not a reissue of an archtop tradition, and it was not designed to be one.
The instrument sits at the intersection of three established voices — the resonance and projection of an archtop, the percussive attack and rhythmic drive of a gypsy jazz guitar, and the focused electric clarity of a thinline. It is not the sum of those three. It is a fourth thing, built with the lessons of all of them.
That positioning shapes specific design choices — and one of them deserves to be addressed directly.
The core of the Aeri is a sculpted internal chassis, machined as a single continuous structure from neck block to tail block. It replaces the traditional combination of kerfed linings, glued blocks and tonebars with one unified load-bearing spine — carved to deliver stiffness exactly where the instrument needs it, and removed everywhere it doesn't.
The result is an archtop that holds its geometry under string tension over decades, resists seasonal movement, and routes energy through the top with a clarity that bonded internal components cannot match. Every Aeri shares the same internal structure, machined to the same tolerances, instrument after instrument.
Both Aeri and Aeri HL are built around this chassis.
The top, back and bellycut are inlayed flush into the body sides — no binding channels, no protruding edges. The transition between top, side and back is a single continuous, rounded surface.
Two consequences: a cleaner visual line, with the figure of the top reading uninterrupted to the edge of the instrument, and a far more comfortable instrument against the body and forearm. Traditional archtop binding is replaced by precision joinery and a fully rounded perimeter.
The Aeri introduces a belly cut to the archtop format — a contoured relief on the back where the instrument meets the player's torso. Combined with the rounded perimeter and a forearm bevel on the upper bout, it transforms the playing position of an instrument that has historically offered none.
An archtop you can play sitting, standing, or for an entire session without the body fighting you.
Aeri retains Belforti's signature no-heel architecture: a bolt-on neck joint engineered to disappear under the hand, with full unobstructed access to the upper frets. The bolt-on configuration means the neck is fully serviceable — removable, reshimmable, replaceable — without the irreversible procedures a set or glued neck would require on an instrument of this caliber.
A modern archtop should be a working instrument, not a fragile object. Aeri is built to be played hard and serviced cleanly.
Aeri
The traditional archtop expression of the Aeri concept. Full headstock, straight frets, conventional scale length. Twenty-four stainless steel frets, dual carbon fiber neck reinforcement, headstock-access truss rod.
For the player who wants the silhouette, balance and visual identity of an archtop — built on a modern chassis, with modern ergonomics, and serviceable for a working musician's lifetime.
Aeri HL
The headless, multi-scale variant. Fanned frets across a custom scale range, headless tuning hardware at the bridge, and an ergonomic neck profile shaped for extended playing in any position.
The headless format removes the mass and the leverage of a traditional headstock — the instrument balances differently against the body, sits lighter on a strap, and tunes from the bridge end. Multi-scale fretting matches scale length to string range, tightening the low end and easing tension on the treble strings.
For the player who treats the archtop as a forward-looking instrument, not a heritage object.
Both configurations share the same chassis, the same inlayed top and back, the same belly cut and rounded perimeter, the same no-heel bolt-on architecture, and the same 24 stainless steel frets.
The Aeri is built to be looked at as carefully as it is played. Beyond the chassis and the architecture, the instrument carries a set of deliberate design details — drawn from traditional archtop hardware but redesigned, rebuilt, and made entirely in-house. Every visible component is ebony. Every component does its job better than the part it replaces.
Ebony Floating Tailpiece
A floating tailpiece anchors the strings to the lower bout while letting the top vibrate freely — the traditional archtop approach to mounting hardware without dampening the soundboard. Aeri's tailpiece is shaped from a single piece of ebony, finished to the same standard as the fretboard, and engineered to clear the top with a clean shadow line. The mass is calibrated for sustain and string return; the geometry is calibrated for visual balance with the bridge and pickguard. No metal, no plating, no compromise on resonance.
Ebony Thumbwheels with Notched Sides
The bridge thumbwheels are turned from ebony and notched on their outer faces — a small detail, but one that transforms the experience of setting action. The notches give the fingertips real purchase, allowing precise, controlled height adjustments without slipping or over-tightening. Most archtop thumbwheels are smooth metal cylinders that resist careful adjustment under tension. Aeri's are designed to be turned by hand, by the player, in tune, on stage if necessary.
Dual Intonation Ebony Bridge
A floating ebony bridge, machined with a dual intonation profile — engineered to work cleanly with both flatwound and roundwound strings. Most floating archtop bridges are intonated for a single string type, forcing the player to commit to flats or rounds for the life of the instrument or accept compromised intonation when switching. Aeri's bridge solves the problem at the geometry level: two intonation paths cut into a single bridge, allowing the player to move between string types without rebuilding the saddle. Ebony throughout — for the resonance, for the visual coherence with the rest of the hardware, and for the longevity.
Ebony Pickguard
The pickguard is shaped from solid ebony, mounted floating off the top in the traditional archtop manner. No plastic, no laminated layers, no printed grain. The pickguard reads as a continuous design element with the tailpiece, the bridge, and the thumbwheels — a single material, four components, one visual language. It is also the easiest detail on the instrument to dismiss as decorative, and the easiest to recognize as not.
Both Aeri and Aeri HL are offered in single or dual pickup configurations.
Single pickup — a focused, vocal voice, with a clean upper bout and minimum visual interruption of the top.
Dual pickup — full tonal range, neck-and-bridge versatility, traditional archtop options expanded into modern territory.
Pickup choice is open. Belforti specifies and sources to the player's preference — humbuckers, mini-humbuckers, P-90s, floating or top-mounted. We will discuss the right voice for the instrument as part of the build conversation.
On the Neck Pickup Position
Aeri carries 24 frets. On a traditional archtop with 19 or 20 frets to the body, the neck pickup sits at a fixed harmonic location — typically over the 24th-fret node — and produces the warm, dark, vocal voice that the format is known for. On Aeri, the extended fretboard moves the neck pickup further toward the bridge, into a different harmonic position.
This is intentional. The neck pickup on Aeri is voiced for clarity and articulation rather than the smoky, dark register of a vintage archtop. The instrument is not trying to reproduce a 1950s ES-175 voice. It is offering a voice of its own — bright at the top end, present in the midrange, with the resonance of a chambered archtop body behind it.
For a player looking specifically for a traditional archtop neck-pickup tone, Aeri is not that instrument. For a player looking for what an archtop could be when designed for a contemporary musical context, it is exactly that.
The voicing is the point. The instrument was designed around it, not in spite of it.
Still a Belforti
For all that the Aeri redefines on the archtop format, it remains unmistakably a Belforti. Every instrument that leaves the workshop carries the same foundation — the construction standards, the playing standards, and the service standards that define what we build, regardless of model.
Traitement PLEK
Chaque guitare Belforti subit un traitement PLEK méticuleux, un processus de haute précision qui nivelle les frettes à la perfection, améliore la jouabilité et assure une action optimale. Cette technologie de pointe garantit que votre instrument est réglé avec la plus grande précision pour un confort et une jouabilité inégalés dès la sortie de l'étui.
Manches renforcés en titane
Chaque manche est renforcé intérieurement par de doubles tiges en titane, préservant la rigidité et la stabilité dans le temps, les voyages et les climats.
Combiné à des bois de lutherie soigneusement sélectionnés, il maintient la résonance tout en empêchant le gauchissement ou les points morts.
Extrémités de frettes invisibles
Les extrémités des frettes sont parfaitement intégrées à la touche, éliminant les soies saillantes et le besoin de binding.
Cette technique assure un bord parfaitement lisse, une durabilité exceptionnelle face aux changements d'humidité et une esthétique raffinée aussi agréable au toucher qu'à la vue.
Accès facile à la tige de réglage
Pour un réglage facile et précis de la courbure du manche, les instruments Belforti utilisent un système de truss rod à roue accessible directement au talon — pas besoin de retirer les cordes ou les accessoires.
C'est une fonctionnalité professionnelle née de la pratique en atelier, intégrée à chaque instrument.
Spécifications techniques
6 cordes
Nut Width : 44mm
Width at Last Fret : 60mm
Rayon de la touche (3 options)
Vintage 9"-12" / Équilibré 10"-14" / Moderne 12"-16"
Profils de manche (5 options)
Petit / Moyen / Grand / 3D Nest™ / 3D Flow™
Diapason (3 options)
Aeri : 25" / Aeri HL : 26" to 25"
Nombre de frettes : 24
Espacement des cordes au chevalet : Espacement égal de 10,5 mm
Lower Bout : 370mm
Shoulders : 270mm
Total Length : 100cm
Thickness : 50mm
7 cordes
Largeur au sillet : 48mm
Largeur à la dernière frette : 70mm
Rayon de la touche (3 options)
Vintage 9"-12" / Équilibré 10"-14" / Moderne 12"-16"
Profils de manche (5 options)
Petit / Moyen / Grand / 3D Nest™ / 3D Flow™
Diapason (3 options)
Aeri : 25" / Aeri HL : 26" to 25"
Nombre de frettes : 24
Espacement des cordes au chevalet : Espacement égal de 10,5 mm
Lower Bout : 370mm
Shoulders : 270mm
Total Length : 100cm
Thickness : 50mm
8 cordes
Largeur au sillet : 54mm
Largeur à la dernière frette : 80mm
Rayon de la touche (3 options)
Vintage 9"-12" / Équilibré 10"-14" / Moderne 12"-16"
Profils de manche (5 options)
Petit / Moyen / Grand / 3D Nest™ / 3D Flow™
Diapason (3 options)
Aeri : 25" / Aeri HL : 26" to 25"
Nombre de frettes : 24
Espacement des cordes au chevalet : Espacement égal de 10,5 mm
Lower Bout : 370mm
Shoulders : 270mm
Total Length : 100cm
Thickness : 50mm
Built to Order
Aeri is a standalone model, built to order outside our series structure. Each instrument is configured in direct conversation between the player and the workshop — top wood, finish, pickups, hardware, neck profile, and the choice between Aeri and Aeri HL.
Contact the Montrouge showroom or workshop to begin a build.